MDH and local agencies
Kits are sold through local health departments, hardware stores, and labs. MDH’s testing page lists local contacts and a discounted path for Minnesota residents. Some kits bill the lab fee when you mail them.
MDH testing pageCommunity guide · Twin Cities
A short-term mail-in kit is how Minnesota says to start. This guide follows MDH’s placement rules, explains a result near 4.0 pCi/L, and keeps consumer monitors in their lane.
Reviewed for accuracy against EPA and Minnesota Department of Health guidance — September 22, 2026.
On this page
Should I test?
Minneapolis is in Hennepin County, and Hennepin County is Zone 1 on the EPA Map of Radon Zones. Ramsey, Dakota, Washington, Carver, Scott, Wright, and Sherburne are Zone 1 as well. Anoka, Chisago, and Isanti are Zone 2. A Zone 2 county has a predicted average screening level between 2 and 4 pCi/L, not a free pass. EPA says homes over the action level show up in every zone, and the map is not a reason to skip a test during a sale.
MDH is more specific about Minnesota than a national map can be. The department says the average radon level in Minnesota is more than three times the U.S. level, because of geology and because homes here are closed or heated most of the year. MDH also says more than two in five Minnesota homes have levels that pose a significant health risk. Those are statewide statements. They are not a Longfellow average, a Linden Hills average, or a North Loop average. This guide does not invent neighborhood numbers. County context, if you want it, lives on MDH’s radon data portal. Read it there. Do not treat a portal chart as your unit.
Radon in Minnesota is the gas from uranium and radium in rock and soil. MDH describes soil as the main source. The house often runs at lower pressure than the outdoors, so some replacement air is pulled from the soil through slab cracks, floor-wall joints, an open sump, or a crawl space. The stack effect is stronger in a taller house in January, when warm air leaves the top and makeup air enters low. A 1920s Minneapolis duplex and a new rambler in the suburbs can both do this. Foundation type does not grant an exemption.
The sentence to keep: every Minneapolis home should be tested, and a short-term kit is how MDH says to start.
Zones are EPA’s June 2024 county designations. Anoka is Zone 2 on purpose: the Twin Cities are not one color. This is not a neighborhood heatmap, and it is not a substitute for a test.
MDH recommends mitigating at 4 pCi/L or higher and says a system can be considered between 2 and 4. Get there with the two-test path, not a single screen glance.
How a kit works
On the testing page, MDH splits kits into two jobs. A short-term test usually runs 2 to 7 days and is the screen you start with. A long-term test runs at least 90 days, should cover some heating and some non-heating weather, and is the better estimate of the annual average.
Placement is not the Colorado rule, and it is worth reading slowly if you have used a kit in another state. MDH says to test the lowest level you regularly use. If you spend more than about 10 hours a week in the basement, test the basement. In a sale, test the lowest level, basement included. Put the device at least 20 inches off the floor, preferably around breathing height, 1 foot from exterior walls, 3 feet from exterior windows, and away from drafts, kitchens, baths, laundry, fireplaces, and furnaces.
Any test shorter than three months needs closed-house conditions: windows and exterior doors shut except for normal entry, heating and cooling running as you normally run them. Short-term tests can happen any time of year. MDH says the heating season is the better time. If the weather is severe or unusually windy, wait.
The decision rule is also Minnesota-specific. Do two tests before you mitigate, unless a licensed professional used a continuous monitor in a real estate transaction. MDH’s first-result path: about 0 to 1.9 pCi/L, retest in 2 to 5 years; about 2 to 7.9, follow with a long-term test; 8 or higher, follow with another short-term test. Then use the long-term result, or the average of two short-term results. At 4 or above, MDH recommends mitigating. From 2 to 3.9, consider a system. Under 2, retest in 2 to 5 years. The how to test page puts that sequence in order.
Borderline results
MDH uses EPA’s 4 pCi/L action level and says a system can be considered between 2 and 4 so the level goes as low as practical. A first kit at 3.5, 4.2, or 4.8 is not a mitigation order and not an all-clear. On MDH’s chart, a first result from 2 to 7.9 calls for a long-term follow-up. The long-term result, not the scary Tuesday on a digital display, is what you compare with 4.
A continuous consumer monitor can still help you see the heating-season swing MDH describes: stack effect, exhaust fans, a clothes dryer, an old furnace, wind over the roof. Watch it for weeks in the same lowest room you actually use. Then let an approved long-term device or a second approved short-term test make the decision.
MDH is direct about the limits of store-bought digital monitors. Consumer digital radon monitors often cost about $100 to $200. They have not had a full evaluation, they are not approved by the national proficiency programs, and MDH does not recommend them for a real estate transaction or for the mitigation decision. Use one as a trend notebook between approved tests. Do not walk into a purchase agreement waving a living-room monitor. The monitor page keeps that line bright.
If the approved follow-up is at or above 4, hire an MDH-licensed mitigator. If it lands between 2 and 3.9, MDH says you may consider a system. Either way, the license matters more than a national card. Industry certification alone is not enough to test or mitigate a Minnesota building you do not own or lease.
If it stays high
When the follow-up says mitigate, MDH’s usual fix is the same soil-suction idea EPA describes: a pipe and a fan draw soil gas from under the slab and exhaust it above the roof. Hennepin County says sealing cracks is basic and, by itself, has not been shown to lower radon in a reliable way. MDH’s mitigation page tells owners to avoid unlicensed installers and to be skeptical of bids under $1,000. Get the bid in person. Ask for the installer’s individual MDH license number, whether the price is firm, and whether an electrician is included if a new circuit is required.
Two public cost ranges are in print, and they are not identical. MDH’s real-estate brochure says a system averages about $1,500 to $3,000. Hennepin County’s radon page says the average is about $1,800, with a range of about $500 to $2,500 depending on construction. Quote both, then take itemized bids. This guide does not blend them into a new number. MDH financial assistance is a separate page. Eligibility is whatever that page says today.
The person who mitigates a building they do not own or lease must be licensed by MDH. An NRPP or NRSB listing can be useful, and it does not replace the state license. Search MDH’s service-provider list and read how licensing works. Systems installed on or after September 1, 2020 should carry an MDH system tag on the pipe near the U-tube. You can ask MDH for a free inspection of a recent system.
After installation, MDH’s real-estate guidance says to run an independent short-term test with the system operating, then retest the house about every two years. The general homeowner retest interval elsewhere on MDH’s site is every 2 to 5 years, and also after you finish a basement, add insulation, replace windows, or change the heating system. A passive vent with no fan is not the same as an active system. MDH’s new-construction page says Minnesota homes have been required to include passive radon-resistant features since 2009, including a vent pipe and not a fan. Test after you move in. Activate the system with a fan if the test says you need to.
Buy or get a kit
Kits are sold through local health departments, hardware stores, and labs. MDH’s testing page lists local contacts and a discounted path for Minnesota residents. Some kits bill the lab fee when you mail them.
MDH testing pageThe county page repeats kit options and says staff can provide a list of certified mitigators. That list is theirs to give, not one printed here. Phone published by the county: 612-543-5200.
Hennepin County radon pageAnyone testing a building they do not own or lease needs an MDH license. National certification is not enough. Use the state provider search for a transaction.
Find a measurement professionalThe link does not apply this discount. Add the monitor to your cart and enter your name and shipping. After those are in the cart, type ARS10-10OFF at checkout. Airthings takes 10% off.
MDH says a consumer digital monitor is not the test for a sale and not the basis for a mitigation decision. If you want a diary while an approved follow-up runs, these Airthings models are the ones linked here. American Radon Systems does not install in Minneapolis. A high approved result goes to MDH’s provider search.
ARS10-10OFF is 10% off, and it is not filled in by the product link. Enter it at checkout only after your name and shipping are in the cart. We may earn a commission if you buy through these links. Follow the manufacturer’s placement instructions. A consumer monitor is not a real-estate report and not a mitigation decision by itself.
Local resources
These are directories and official pages. This guide does not name, rank, or recommend individual mitigation companies.
Statewide context, the smoking-and-radon table, and why closed heating seasons matter.
Open official pageShort-term versus long-term kits, placement, and the two-test decision chart.
Open official pageMinnesota Radon Awareness Act disclosure rules. Testing is recommended, not required to close.
Open official pageMeasurement and mitigation professionals licensed by the state. Not a paid directory from this guide.
Open official pageWhy an NRPP card alone does not authorize radon work in Minnesota.
Open official pageSince 2009, new Minnesota homes need passive features, including a vent pipe and not a fan.
Open official pageMDH’s page for help paying for mitigation. Rules live there, not in this guide.
Open official pageCounty context from MDH. This guide does not copy those charts into neighborhood claims.
Open official pageLocal kit options, why sealing alone falls short, and the county’s published cost range.
Open official pageUseful context. The MDH license is still required for work in Minnesota.
Open official pageNational directory. Same Minnesota rule: state licensure comes first.
Open official pageHow EPA tells you to start with the state program, then the national lists.
Open official pageHennepin is Zone 1. Anoka is Zone 2. Test either way.
Open official pageNational testing guide, including why a neighbor’s result is not yours.
Open official pageHow soil-suction systems work and why caulk is not a standalone fix.
Open official pageCurrent index of EPA radon guides.
Open official pageMDH’s mitigation-professional finder and hiring questions, including the warning about very low bids.
Open official pageFAQ
Radon is a colorless, odorless gas from the natural decay of uranium and radium in rock and soil. MDH says it can build up indoors, decay into fine radioactive particles, and damage lungs over years of breathing it. The department estimates 21,000 lung-cancer deaths a year in the United States from radon. There is no scent to warn you. A test is the only way to know the level in a Minneapolis house. See MDH’s radon in homes page.
Because the house, not the block, holds the number. MDH recommends that every Minnesota home be tested. Homes here spend much of the year closed and heated, which MDH ties to higher indoor levels, along with the state’s geology. A tidy bungalow in Tangletown and a warehouse conversion can share a soil source and still test far apart. Looking at the neighbor’s report is the myth EPA already retired.
No. Hennepin County, which contains Minneapolis, is EPA Zone 1. So are Ramsey, Dakota, Washington, Carver, Scott, Wright, and Sherburne. Anoka, Chisago, and Isanti are Zone 2 on the same EPA map. Zone 1 means a predicted average indoor screening level above 4 pCi/L. Zone 2 means a predicted average between 2 and 4. Neither zone is your unit’s result. Elevated houses exist in both. Test the house. The map is on EPA’s zone page.
MDH uses EPA’s action level of 4 pCi/L and recommends a mitigation system at 4 or higher. Between 2 and 4, MDH says a system can be considered so the level is as low as practical. Any radon carries some risk, and zero is not a realistic target. The decision for a homeowner still follows MDH’s two-test path on the testing page, not a single afternoon on a consumer monitor.
Start with a short-term test. MDH says a short-term kit, typically 2 to 7 days, is the screen, and a long-term test of at least 90 days is the better annual average. Which follow-up you use depends on the first result: long-term if the first test is about 2 to 7.9 pCi/L, another short-term if it is about 8 or higher. A long-term test should include some heating weather and some milder weather.
Follow the device, inside MDH’s window of about 2 to 7 days for a short-term screen. Check the expiration date before you open it. Do not end the test early because guests arrive. While it is out, keep the closed-house conditions MDH requires for any test under three months. Ship it as the lab instructions say, and keep a photo of the start and stop times.
Test the lowest level you regularly use. MDH’s example is the basement if you spend more than about 10 hours a week there. In a sale, test the lowest level. Hang or set the kit at least 20 inches above the floor, ideally near breathing height. Keep it 1 foot from exterior walls, 3 feet from exterior windows, and away from drafts, high humidity, and heat sources such as fireplaces and furnaces. Kitchens, baths, and laundry rooms are the wrong rooms.
For any test under three months, MDH says keep windows and exterior doors closed except when people actually enter or leave. Run the heating and cooling the way you normally do. Winter makes this easier because the house is already shut, which is also why MDH calls the heating season the better time for a short-term test. A test with the storm windows off and the sash cracked is not a closed-house test, even if it is only cracked “for air.”
Yes. MDH says weather can change indoor radon and that you should wait to start a short-term test if the weather is severe or unusually windy. Wind over the roof and exhaust fans are two of the pressure effects MDH names. There is no local correction you can multiply by after the fact. Wait for an ordinary week, then test.
If that was your first short-term test, MDH’s chart sends a result in the 2 to 7.9 band to a long-term follow-up, not straight to a contractor. Use the long-term result to decide. At 4 or above, mitigate. From 2 to 3.9, consider a system. A consumer digital monitor may show you the weeks in between, and MDH says not to let that monitor make the mitigation call. Confirm with an approved device.
MDH describes three pressure drivers: the stack effect as warm air leaves the top of the house, wind over the roof, and appliances or fans that exhaust air so soil gas is pulled in to replace it. A closed January week and an open June weekend are different tests. So are a basement family room and a second-floor bedroom. EPA’s Citizen’s Guide says short-term results are simply less stable than a long-term average. That is expected, not a sign the lab cheated you.
Not for the decisions that matter. MDH says consumer digital monitors usually cost about $100 to $200, have not been fully evaluated, are not approved by the national proficiency programs, and should not be used in a real estate deal or to decide on mitigation. A mail-in short-term kit, a long-term alpha-track, or a licensed professional’s approved continuous monitor are the decision tools. A living-room monitor is optional trend context. The Airthings button does not apply ARS10-10OFF. Once the cart has your name and a shipping address, enter the code yourself for 10% off. We may earn a commission if you buy through those links. That does not change MDH’s rule. Details are on the testing page. American Radon Systems does not install in Minneapolis.
MDH says kits are inexpensive and sold by local health departments, hardware stores, and labs, and that some kits charge the analysis fee when you mail them. Read who the lab is, whether the device is short-term or long-term, and the expiration date. Minnesota residents can use the discounted kit path MDH describes, including the Air Chek discount MDH notes, by starting from MDH’s testing page rather than a random coupon link. For a sale, hire an MDH-licensed measurement professional instead.
Start with MDH’s testing page and the list of local radon contacts linked there. Many local agencies hand out information and some hand out kits. Hardware stores stock them. MDH also points Minnesota residents to a discounted online short-term kit. Hennepin County Public Health repeats those options and publishes its own contact line, 612-543-5200, for environmental health questions. This guide does not sell kits.
Testing and mitigation are not required to close. Disclosure and education are. Since January 1, 2014, before a purchase agreement is signed, the seller discloses known radon concentrations in writing and provides MDH’s “Radon in Real Estate Transactions” brochure. The disclosure covers tests, records, any mitigation system, and whether results at or above EPA’s action level are known. Buyers and sellers negotiate who tests and who pays for a system. MDH wants a licensed professional for the transaction test. Read the real-estate page and the brochure.
MDH says to run an independent short-term test with the system on, to confirm the reduction, and then to retest about every two years so you know the fan still works. Also retest after you finish space, add an addition, tighten the house, or change heating or cooling. A system tag should be on the pipe for installations on or after September 1, 2020. MDH will do a free inspection of a recent system if you ask the Indoor Air Unit. See the mitigation systems page.
No. Hennepin County says sealing is a normal part of the work and, alone, has not been shown to lower radon consistently. MDH and EPA describe an active soil-depressurization system as the method that usually works: pipe, fan, discharge above the roof. Caulk helps that system. It does not replace it. EPA’s Consumer’s Guide is the national version of the same point.
Because Minnesota licenses the work. MDH says anyone who measures or mitigates in a building they do not own or lease must hold an MDH license. A national certification is not a substitute. Ask for the individual license number and check MDH’s provider search. You may still look at NRPP or NRSB as extra context. The state list is the one that matters in Minneapolis. American Radon Systems does not install here.
The Radon Awareness Act is written for the sale or transfer of residential property, not as a substitute for a lease. You can still test the unit you live in. If someone else performs the test, MDH’s licensing rule applies to them. Building-wide fans and roof pipes are the owner’s project. EPA’s guide for tenants is the national renter explainer. This page does not claim a Minneapolis rental statute it has not cited, and it is not legal advice.
Start with the air. EPA’s Citizen’s Guide says radon in water is a later question: test indoor air first, and look at a private well if air is high. MDH treats soil gas as the main Minnesota source and lists well water as a possible extra path, not the default. A municipal supply is a question for the utility. Do not buy a water treatment system because a neighbor on a different well had a high air test.
Test the unit you occupy, at the lowest level that unit actually uses. A garden-level apartment and a duplex over a tuck-under garage are not the same pathway as a sixth-floor flat, and none of them inherit the neighbor’s result. If a professional tests a building they do not own, they need an MDH license. Mitigation for a whole building is an owner or association decision. MDH’s school and child-care pages are separate programs. They do not set the rule for your flat.
Yes. MDH says that since 2009 new Minnesota homes must be built radon-resistant: sealed entry points and a vent pipe, not a fan. The passive stack relies on natural upward flow. An active fan reduces radon more effectively, and MDH no longer keeps a list of builders who include the fan. EPA says to test every new home after move-in even when resistant features are there. If the test is at or above 4, a licensed mitigator can add the fan to the rough-in.
They do not measure radon and they do not replace a mitigation system. Radon has no odor a pet can reliably report, and MDH’s fix is a licensed soil-depressurization system, not a houseplant or a filter marketed for dust. An air purifier may change other parts of indoor air. It is not the method MDH describes for a result at or above 4 pCi/L. Test with a kit.
The risks stack. MDH’s table for lifetime lung-cancer deaths at an average of 4 pCi/L is about 7 in 1,000 people who never smoked, about 62 in 1,000 people who currently smoke, and about 23 in 1,000 in the U.S. general population. MDH calls radon the leading cause of lung cancer for people who do not smoke and the second leading cause for people who do. Quitting has its own help line through Quit Partner. Reducing the house does not replace that, and this guide is not medical care. The table is on MDH’s radon page.
Every 2 to 5 years for a home that has been tested, and you should keep the report. Sooner if you finish a basement, add on, insulate, replace windows, change the heating or cooling system, or install a mitigation fan. After a system is in, MDH’s real-estate brochure tightens the check to about every two years. A first result under 2 pCi/L still comes back around on that 2-to-5-year clock. It is not permanent.
When you need a third party, especially in a purchase. MDH says most people can run their own test if they follow the instructions, and recommends a licensed professional when the result has to be unbiased. The Radon Licensing Act requires the license for anyone testing a building they do not own or lease. A home inspector who offers radon still needs that license. Ask what device will be used and whether it is approved for a transaction. Start at find a measurement professional.
Use the published ranges and do not average them yourself into a fake quote. MDH’s brochure says about $1,500 to $3,000. Hennepin County says about $1,800 on average, roughly $500 to $2,500 depending on the house. MDH also warns against unusually low bids under $1,000. Consumer digital monitors are a separate, smaller spend, about $100 to $200, and they are not the mitigation decision. Kits themselves are described as inexpensive. Financial assistance may exist. Read that page for current rules.
MDH says you may test any time, and that the heating season is the better time for a short-term test because the house is closed and Minnesota homes stay shut much of the year. A long-term test should deliberately include both heating and non-heating months. A July test with windows open does not describe January. If you only have a summer week, keep true closed-house conditions or wait.
The entry path changes. The need to test does not. MDH says a basement gives soil a large contact area and a taller house can increase stack effect. Slab-on-grade houses still have openings. Crawl spaces sit on soil. Manufactured homes with solid skirting can behave like a crawl space. Test the lowest level people use, at least 20 inches off the floor. Do not place the homeowner kit in the crawl space itself. Mitigation for a crawl space is a contractor question. Hennepin County describes sub-slab depressurization as the usual active fix.
MDH’s passive-construction description includes a 3- to 4-inch vent through the roof and flashing so the roof does not leak. An active system uses that same idea plus a fan. An association may care about the penetration, the fan location, and who pays for a common roof. Ask the association with the contractor’s drawing before work starts. This guide does not invent a Minneapolis association statute. The license and the system tag are still required whoever approves the roof.
The Awareness Act expects the known records: test results, whether a system exists, and the MDH brochure before the purchase agreement is signed. Include dates, the device, the floor tested, and whether a licensed professional ran it. If levels were mitigated below the action level, say so and attach the evidence you have. If you only have a consumer monitor screenshot, label it as that and do not pretend it is the MDH-recommended sale test. The realtor page is the longer version for agents.